Headlight Removal

[DUNGUN007]

CAN SOME ONE TELL ME HOW TO REMOVE THE HEADLIGHTS,SO THAT I CAN INSTALL STROBES IN THEM THANKS

[mwz26]

you shouldnt have to remove them to put strobes in there, just remove the bulps, stick the strobes in and put the bulbs back

[baNanA_ryCe]

i think he wants to drill another hole so he can put strobes in

[DUNGUN007]

YA I WANTED TO DRILL NEW HOLES IN THEM,BUT I WANTED TO KNOW IF I HAVE TO TAKE OFF THE BUMPER TO REMOVE THEM

[caz]

Must you type in all caps?

[DUNGUN007]

Is this better for you ?

[Furies]

go to this website........ its clone gts's website and go to installs and then look for the HID installation......it shows how to get the headlights out...

HERE (http://www.clonegts.com)

[DUNGUN007]

Thanks Bro

[CloNeGTS]

thanks Furies.....beat me to it.

[aZnTrD2k]

I know how to take it out but how do you dis assemble the headlights???

[CloNeGTS]

what do you mean disassemble? What are you trying to get to?

Besides taking out the bulbs, that's all the more you will get apart without melting the plastic welds and pulling the face of the headlight off.

[aZnTrD2k]

GTsnut painted the inside of his headlights and it looked cool.

[ryan_b83]

Hey does anyone have another link to show how to remove the headlight? I am trying to remove the right side headlight and i removed the 2 screws but there i still something holding it on?? any ideas?

thanks!

[robare99]

There is a third screw at the bottom. The easiest way to get at it is to undo the screw in the fenderwell where the bumper meets the fender, then you can pull the corner of the bumper down and can access that third screw at the bottom of the light.

[pnoy]

GTsnut painted the inside of his headlights and it looked cool.


after removing the headlight. remove all the bulbs, and rubbers and anything that melts. Then remove the screws on the sides . Once all removed, pre heat the oven at I think it was 300 degree. Get a towel and lay it on top of the rack together with the headlight. close and wait for 15 mins, the pry the headlight to separate starting from the back.

Hey does anyone have another link to show how to remove the headlight? I am trying to remove the right side headlight and i removed the 2 screws but there i still something holding it on?? any ideas?

thanks!


Only 3 screws... find them! you don't need a manual to remove a headlight

[ryan_b83]

Hum... ok i've removed 2 screws so far... I marked the ones in this picture where i removed the screws.... i cant find the thrid one.. :wtf:
http://www.linxsmart.com/Picture2.jpg

thanx

[oneceli2nv]

http://members.inteliport.net/~easye/
click walk-thru and the first part of the write up will tell you how

[ryan_b83]

you have to take the bumper off to replace the headlight assembly??? :scared:

[oneceli2nv]

you dont have to, you can unscrew just enough for you to stick your hand in there to unscrew the last bolt. In my eyes and from experience, it just makes removal and installation of the headlight easier.

[gAngsTa]

it's very easy.

[ryan_b83]

Ok, got it off, and put the new headlight in...

do you really need to rescrew that 3rd screw back in? was it supposed to have a nut on the other side because its impossible to put ti back together if it does???

[robare99]

I dont believe there is any screw. Probably a threaded tab inside.

[ryan_b83]

ok nevermind, i looked at my old light... there is a little metal thing i gotta put on the new light to screw into... obviously i noticed this right when im putting the last screw in.... lol gotta take it apart again :wtf:

[ryan_b83]

i think im good now and can figure the rest out!! THANKS ALOT EVERYONE!!!

sorry for the dumb questions, im a web designer, not a car guy... (as you probably all can see!)

thanks again!
Ryan

[oneceli2nv]

no prob anytime

[masboy]

i think im good now and can figure the rest out!! THANKS ALOT EVERYONE!!!

sorry for the dumb questions, im a web designer, not a car guy... (as you probably all can see!)

thanks again!
Ryan

I guess we're on the same boat :) thx for this question..