These need to be a sticky

[blitzceli]

2 different techniques with awesome results.


http://www.mr2oc.com/showthread.php?t=305645

and

http://www.mr2oc.com/showthread.php?t=313005

[bloodytiger]

You need to sign in to see it.

[blitzceli]

You need to sign in to see it.

sign up, its free

[jr_castillo847]

Tried still wont work cuz I dont have suffient privileges guess i gotta make some posts what are the links?

[jr_castillo847]

nevermind i gotta be added by a moderator

[blitzceli]

here is link 2. The other is like 10 pages. Well worth the read...

First I sketched out the design on paper. It was nothing fancy just something to use as a loose guide. I changed a few things as I went.

Next the design will dictate what materials you need to use as a base. Since the mr2 is boxy and the lip will be somewhat as well. I went for a 240sx looking rear lip. Just something simple and flows nicely. I chose to use cardboard since imo is the best for a boxy design.

Now that we are about to begin here are some quick tips.
-Wear old clothes
-Spend the extra few bucks to get the latex gloves, if you get resin on your hands it takes some time to get off your hands. Eventually it will turn black from dirt sticking to it and you will look like you never take a shower.
-Design ahead and plan everything out, if you don’t you will waste product, money and time.

Materials you will need and where to buy:
-Masking tape (I like to use the blue painters tape) anywhere
-disposable paint brushes homedepot, lowes, ace
-1.3-1.5 gallons of resin
(polyester is what I used for this) homedepot, lowes or auto supply store
-bondo (2 tubs is what I used)
I used the cheaper filler for this. I usually use ragegold or dynalite homedepot, auto parts store, walmart
-bondo spreaders homedepot, lowes, walmart, auto parts store
-spot putty/glazing walmart, autopart store
-respirator (not recommended, but you will get a headache from bondo and resin if you don’t have one) homedepot, lowes possibly walmart
-spray glue
-chop matt
-fiberglass cloth both dry fiberglass homedepot, lowes, walmart
-Sander
-low grit paper, 60,80 mid grit 120 high 320, 400 600

My advice is to buy all this stuff off the internet, that way you get more for your money and you have more of a selection.

http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0094.jpg


I built the whole lip out of CB (cardboard) first. I then put CB above the lip so no resin got on the bumper. Then cover the whole lip in tape. Put alittle car wax on the lip.


http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0057-1.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0056-1.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0055-1.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0054-1.jpg

.


http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0057.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0056.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0055.jpg



Spray an area of the lip with spray glue, then place the chop matt to the lip, keep doing this until the whole lip is covered in chop matt. Once that is done, mix the resin, apply with the disposable brush. DAB it on! If you apply in strokes the matte will move. Mix the resin in small batches and apply until the chop matt is soaked. After a few coats it will look something like this: Dabbing will also prevent air bubbles down to a minimum. After a few coats it will look something like this:

http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0060.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0059-1.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0058-1.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0059.jpg

http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0058.jpg

Once you get a few coats on and it is sturdy goahead and pop it off the car and remove the CB and tape from the backside Let it sit for a few min so any damp/sticky spots can cure. I then taped off the exposed bumper and mounted the lip. I applied 2 more layers and then pulled it back off the car. I strengthened from the backside. I only did 1 coat because any more would have caused fitment issues.

http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0061.jpg
http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0062.jpg

Once that is done go ahead and sand with 60 grit to knock any standing glass or high spots. Mix up bondo in small batches and apply with the spreader. Apply it smooth as possible because this will prevent more sanding work. I like to do thin layers to avoid a lot of sanding. Trim the lip to the final shape.

http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0074.jpg

http://i5.photobucket.com/albums/y157/flatline16/fg/PIC-0093.jpg

Now that you have it somewhat looking like a lip now take a lot of pictures and upload them to the computer. Look at different angles and you will find more imperfections that you couldn’t see when you were standing there in infront of the lip. Make notes and fix it. Keep doing this until you are satisfied. Once you have it all fixed spray with the better of the primers in the rattle cans (duplicolor high build sandable primer) , dry sand 180-400 then wet sand 320-600. Do this until it is smooth.


http://i5.photobucket.com/albums/y157/flatline16/PIC-0098.jpg
http://i5.photobucket.com/albums/y157/flatline16/PIC-0099.jpg
http://i5.photobucket.com/albums/y157/flatline16/PIC-0100.jpg

I will update the thread with better pictures of the final product this week.

ENJOY!

Here are some finished pics.
http://i5.photobucket.com/albums/y157/flatline16/003-9.jpg