NewCelica.org Forum banner

1 - 20 of 145 Posts

·
Registered
Joined
·
154 Posts
Discussion Starter · #1 ·



The throttle rotor installs in less than 30 minutes, sliding on top of your OEM unit. This product is made of AL6061 Billet Aluminum and then Hard Anodized. The WR Throttle Rotor is Computer Designed to reduce the turning ratio of your throttle body rotor, to increase throttle response and reduce the time it takes your car to get to FULL THROTTLE by 50%.

MSRP: $45
Special: $30 SHIPPED

Paypal me at: [email protected]
Item will ship within 2 business days.
Tracking number will be included and emailed to you.
 

·
Registered
Joined
·
154 Posts
Discussion Starter · #3 ·
This unit installs on top of your OEM Throttle rotor .
Dont need to remove the OEM one.
 

·
Registered
Joined
·
760 Posts
what colors do they come in? Is it just red, silver and blue?
 

·
12+ years daily driver
Joined
·
8,599 Posts
so basically this thing will let you make the throttle cable super tight while staying at that closed position to keep idle from going thru the roof?

Have you sold any of these to celly members of this board? I know you said you have put them on cellys before but anyone's from nc.org?
 

·
Registered
Joined
·
4,118 Posts
can we get a better explanation on how this will reduce the turning ratio of the throttle cable by %50? i just cant seem to picture it in my head..thanks
 

·
12+ years daily driver
Joined
·
8,599 Posts
I am trying to picture it too and from what I am thinking I will have to let the cable out a LOT to reach anything but the lowest insert spot
 

·
Registered
Joined
·
11,645 Posts
im in the area, i can be a tester if needed..
 

·
Registered
Joined
·
543 Posts
i have one i my car, it was realy easy to install and i noticed a little bit better throttle response.
 

·
12+ years daily driver
Joined
·
8,599 Posts
anyone else with experience on this part?
 

·
Registered
Joined
·
11,169 Posts
I'm interested too -- I think if WR offers one to a local for testing and review, a lot of folks would be interested if it is found to work well :)
 

·
Registered
Joined
·
11,645 Posts
=D im local.
 

·
Registered
Joined
·
154 Posts
Discussion Starter · #14 ·
Anyone who is local can come by and try one out.. Just ask for RAY.
If you like it you can buy it. We also offer dyno time for anyone intrested.

While your there you can check out the Race Header also.
 

·
Registered
Joined
·
154 Posts
Discussion Starter · #15 ·
The throttle rotor installs in 30 minutes, sliding on top of your OEM unit. This product is made of AL6061 Billet Aluminum and then Hard Anodized. The WR Throttle Rotor is Computer Designed to reduce the turning ratio of your throttle body rotor, to increase throttle response and reduce the time it takes your car to get to FULL THROTTLE by 50%.
 

·
Registered
Joined
·
11,645 Posts
where are you guys located so i can swing by later this week.
 

·
Registered
Joined
·
19,597 Posts
Carbonized_GT said:
where are you guys located so i can swing by later this week.
let me know when u go. i wanna swing by also. i think they are located in sf.

dont u get the same feeling by just tightening your throttle cable?
 

·
Registered
Joined
·
11,645 Posts
their website doesnt even show their address.
 
1 - 20 of 145 Posts
Top